Product Page :     Firmware Version :  1.17_PT

Setup Wizard
The Setup Wizard is a useful and easy utility to help setup the device to quickly connect to your ISP (Internet Service Provider) with only a few steps required. It will guide you step by step to configure time zone, and WAN settings of your device. The Setup Wizard is a helpful guide for first time users to the device.

WAN Settings
WAN Settings are settings that are used to connect to your ISP. These settings may be referred to as Public settings. These settings are provided to you by your ISP. Please select the appropriate option to connect to your ISP.

PVC
Leave the set at the default value 0 the first time the Router is set up. For more information on this option see Multiple PVC Operation.
VPI
If instructed to change this, type in the VPI value for the initial connection (using PVC 0). Default= 8.
VCI
If instructed to change this, type in the VCI value for the initial connection (using PVC 0). Default= 35.
Virtual Circuit
The Virtual Circuit over which this PPP data is sent. The VC identifies the physical path the data takes to reach your ISP.
Service Category
Select the ATM service category.
PCR
Leave the set at the default value 0 the first time the Router is set up. For more information on this option see Multiple PVC Operation.Enter the ATM PCR value.

WAN - Dynamic IP Address
Select this option if your ISP provides you an IP address automatically. This option is typically used for Cable services. Please enter the Dynamic IP information accordingly
WAN - Static IP Address
Select this option to set static IP information. You will need to enter in the Connection type, IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format. Example: 192.168.0.100
WAN - PPPoE/PPPoA
Select this option if your ISP requires you to use a PPPoA/PPPoE connection. This option is typically used for DSL services. Select PPPoA/PPPoE to obtain an IP address automatically for your PPPoA/PPPoE connection. Please enter the information accordingly.
WAN - Bridge Mode
The modem can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN. Please set the Connection type.
Top

Setup Select to setup basic wireless parameters.

SSID
The service set identifier ( SSID ) or network name. It is case sensitive and must not exceed 32 characters, which may be any keyboard character. You shall have selected the same SSID for all the APs that will be communicating with mobile wireless stations.
Channel
Select the appropriate channel from the list provided to correspond with your network settings. You shall assign a different channel for each AP to avoid signal interference.
Security
There are 2 types of security to be selected. To secure your Wireless Networks.

WEP
Make sure that all wireless devices on your network are using the same encryption level and key. WEP keys must consist of the letters "A" through "F" and the numbers "0" through "9."
WPA
802.1x:
WPA RADIUS uses an external RADIUS server to perform user authentication. To use WPA RADIUS, enter the IP address of the RADIUS server, the RADIUS Port (default is 1812) and the shared secret from the RADIUS server.
PSK:
Is a special mode of WPA for home users without an enterprise authentication server and provides the same strong encryption protection.To use WPA Pre-Shared Key, enter a password in the WPA Shared Key field between 8 and 63 characters long.

Top

LAN Settings
These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. The default IP address is 192.168.15.1 with a subnet mask of 255.255.255.0. You may enter a local domain name for the LAN network if you prefer.

DHCP Server
DHCP stands for Dynamic Host Control Protocol. The DHCP server gives out IP addresses when a device is booting up and request an IP address to be logged on to the network. That device must be set as a DHCP client to "Obtain the IP address automatically". By default, the DHCP Server is enabled. The DHCP address pool contains the range of the IP address that will automatically be assigned to the clients on the network.
Starting IP address
The starting IP address for the DHCP server's IP assignment.
Ending IP address
The ending IP address for the DHCP server's IP assignment.

DHCP client computers will have their information displayed in the Client Table. The Client Table will show the Host Name, IP Address, MAC Address each client computer.

Top

Automatic Time Configuration
Select this option if you want to synchronize the router's clock to a Network Time Server over the Internet. If you are using schedules or logs, this is the best way to ensure that the schedules and logs are kept accurate.
NTP Server Used
Select a Network Time Server for synchronization. You can type in the address of a time server or select one from the list. If you have trouble using one server, select another.
Time Zone
Select your local time zone from pull down menu.

Top

Copyright © 2004-2008 D-Link Systems, Inc.